Equipment and technologies for mechanized wall plastering, pros and cons

Tags:Finishing

Plastering walls, regardless of whether it is performed indoors or on the facade of a building, performs several functions. The main ones are leveling the surface and increasing thermal insulation. This mandatory stage is one of the most time consuming and time consuming. Therefore, much attention is paid to the issues of its mechanization. This article will consider the main devices for mechanized plastering of walls, the pros and cons of mechanizing the process, the application technology. And also a brief overview of the most popular manufacturers and their products is given.

Mechanized plastering of walls: pros and cons

These are the plastering stations used in mass construction. Model ШС-4/6 manufactured by Remstroydormash plant
PHOTO: remstroy.info

The content of the article

1 What is mechanized wall plastering
2 Pros and cons of mechanized wall plastering
3 Varieties of devices for mechanical plastering
4 General technological process of mechanized plastering
5 Leading equipment manufacturers and their products
6 Summing up

What is mechanized wall plastering

When manually applying plaster mixes to the work surface, the pressure required for adhesion between the finish and the wall is provided by the plasterer. With the mechanized (machine) method of application, the plaster mortar is supplied under the pressure necessary for uniform distribution over the surface with the creation of the required adhesion.

Most machine plastering devices use a pneumatic feeding method, but there are models based on a mechanical method of application.

Robot plasterer applying the working mixture mechanically
PHOTO: i.ytimg.com

Important! For mechanized plastering, only special dry building mixtures are used. The use of ordinary or home-made plasters will not only not give the expected result, but can also lead to damage to expensive equipment.

Pros and cons of mechanized wall plastering

There are several technologies for the mechanical method of applying plaster.Their principle of operation, the degree of mechanization, automation of mixing processes and control of the amount of water differ significantly from each other. However, there are common advantages and disadvantages for such devices.

High speed of finishing works, regardless of the type of surface to be treated. Depending on the type of plaster (cement or plaster), the advantage over manual application is 4 to 7 times.
Increased adhesion... The ejection force of the finishing mixture provided by the plastering stations is higher than the efforts applied by most master plasterers. Moreover, it is the same throughout the entire workflow. This gives the finish much better adhesion to the substrate surface.
No cracking when dry. Subject to all application conditions, the plaster mixture is pressed against the base with equal force over the entire treated area. In addition, the application speed allows you to work out large areas without interruptions, without joining the treated areas with already dried ones. Due to the difference in the course of the dehydration process, it is in such places that cracks form.
Savings on consumables. This statement is rather controversial. As a rule, manufacturers of plaster mechanization devices claim that their equipment provides a reduction in the consumption of finishing materials, compared to manual application. However, with the wrong choice of the plastering mode and the viscosity of the solution, a significant part of the finish will go into working off, beating off the wall. By analogy with the evidence from manufacturers, it can be argued that master plasterers can use the entire finishing mixture without a trace, which, in turn, gives them an advantage in saving mortar over plastering stations. Therefore, the statement about saving consumables seems to be just a marketing ploy.
Total savings in finishing costs. Directly depends on the volume of work performed. On the one hand, ready-made plaster mixes for machine application are somewhat more expensive than their manual counterparts. In addition, one should take into account the costs of electricity and equipment rental or hiring highly qualified specialists with their own installations, whose services, of course, are more expensive. On the other hand, high speed of work execution. Also, when using manual plastering, it is necessary to involve a much larger number of workers.
Versatility. Plastering stations can be used for automatic mixing of other finishing materials or when pouring cement-sand screeds.

Plastering station versus plasterer
PHOTO: i.ytimg.com, profosnova.ru

There are also a number of rather significant shortcomings.

Volatility. The plaster station and other means of mechanization require electricity to operate. Therefore, at remote sites that are not connected to power supply systems, their operation will require an additional diesel generator.
High cost of equipment. These are high-tech plastering stations. Simpler means of mechanization, such as a hopper bucket, are much cheaper. But their productivity is not much higher than that of a master plasterer.
Personnel qualifications. Some experience is required to work with complex equipment. In addition, it needs maintenance and thorough cleaning every time after work.

Related article:

How to plaster walls with your own hands for a beginner: video and features of application on various surfaces, step-by-step photo instructions, consumables and tools.

Varieties of devices for mechanical plastering

Today, craftsmen are offered a wide range of equipment for machine application of finishing materials. It can be a hand tool with a minimum degree of mechanization (hopper bucket, in other words a pneumatic shovel or a pneumatic gun) or automated plastering stations.Let's consider each of the varieties of these devices in more detail.

Plastering station Grand 4
PHOTO: prostanki.com

Hopper (pneumopath)

The hopper bucket consists of a container (3-5 l) in the lower part of which there are 4 holes through which the plaster mix is sold. Inside the bucket, opposite these holes are air nozzles. The package includes a telescopic handle with a compressed air control handle. Hose and compressor sold separately. The compressor must have a capacity of 35-45 m³ / h and a pressure of 4-6 atmospheres.

Hopper bucket, a compressor is required to use it
PHOTO: encrypted-tbn0.gstatic.com

The plastering process is simple and does not require extensive prior training. The pre-mixed plaster mortar is scooped up with a ladle. The hopper is brought to the wall at a distance of 10-15 cm. After that, the compressed air supply is switched on.

Advantages:

ease of use;
affordable cost.

Disadvantages:

it is necessary to purchase additional equipment;
rather large losses of the plaster mixture.

Hopper technology: video

Pneumatic pistol (cartridge pistol)

Consists of one nozzle on a pistol grip, to the top of which a metal or plastic container (up to 9 liters) for plaster is attached. The principle of operation is the same as that of the hopper. Has replaceable nozzles for the nozzle (diameter 3-8 mm), which allows the use of finishing mixtures of various consistencies. It can be used not only for rough plastering, but also for decorative finishing or applying textured spray.

Cartridge pistol for applying textures WESTER KP-10
PHOTO: cdnmedia.220-volt.ru

Advantages:

ease of use;
affordable cost.

Disadvantages:

it is necessary to purchase additional equipment;
comparatively low speed of finishing.

Plastering stations

They have a rather complex design. The main elements are:

hopper for raw materials (dry plaster);
container for mixing and storing the mixed mixture;
auger primary feed system;
compressor;
Control block.

Principal design of the plaster station
PHOTO: stroiformat.com

According to the manufacturers' recommendations, it is rational to use such equipment in rooms with an area of at least 30 m². Immediately after completion of work, all containers and hoses for supplying the finished mixture must be thoroughly rinsed with clean water. As a rule, there are special cleaning modes, so this procedure is not too complicated and tedious.

Advantages:

high speed of plastering;
kneading process automation;
high quality processing of the base.

Disadvantages:

high price;
an appropriate qualification is required.

Robot plasterer

This is an installation for applying plaster mixtures to flat vertical walls. The distributing part of the device moves along guides that are fixed on the floor and ceiling of the room. The robot needs to knead the plaster separately, but you can use the usual hand-applied mixes. The plant productivity is up to 80 m² / hour. The robotic plasterer cannot be used to decorate rooms above 7 m, staircases and facades.

Robot plasterer, model RoboPlaster-1000, but in terms of functionality, it is rather a semiautomatic device
PHOTO: stroiformat.com

Advantages:

high performance;
the quality of finishing does not depend on the professionalism of the staff;
can use conventional plaster mixes.

Disadvantages:

very high cost;
cannot be used for finishing ceilings, staircases and facades.

The process of operation of a robotic installation for plastering can be seen in the video:

h3>Plaster and trowel equipment

Plastering disc machines are used for leveling plastered walls and ceilings both with manual and mechanized finishing. Foam or chipboard is used as trowels.

Rokamat Nautilo plastering machine
PHOTO: vbt.by

The working nozzle is connected to the power drive using a flexible shaft. This reduces vibration, making the grouting process even easier. The power drive is an electric motor with a squirrel-cage rotor, operating from a three-phase current with a voltage of 42 V and a frequency of 200 Hz. Such parameters of electricity allow the operator not to be afraid of electric shock even when working on wet and wet surfaces.

There are two main types of plastering machines:

Single disc. For example, SO-112B, the circle rotates in one direction.
Two-disk. For example, SO-86B. It has two circles, an inner and an outer (in fact, a ring), which rotate in different directions.

The process of grouting plaster is perfectly illustrated by the proposed video:

h2>General technological process of mechanized plastering

The process of preparing installations for mechanized plastering for operation may differ significantly depending on the type of device. However, there are general rules and recommendations that must be followed, these are:

Preparation of the base.
The sequence of the plastering process.
Grout - leveling the coating.

Preparing the plaster station for work
PHOTO: i.ytimg.com

Preliminary surface preparation

Preparation of the surface of walls and ceilings for plastering using mechanical means practically does not differ from ordinary measures:

The surface of the base is cleaned from dirt and dust. Old trim is removed if necessary.
Metal embedded parts are treated with anti-corrosion properties.
Irregularities and defects are corrected if their relief exceeds 1.5-2 cm.
The base material is treated with an appropriate primer.
Concrete (and other dense materials) - by concrete contact.
Porous and hygroscopic - deep penetration primer.
If necessary, beacons are installed, along which alignment is carried out.

Preliminary surface preparation before plastering - priming with a spray gun
PHOTO: i.ytimg.com

The process of applying the plaster mixture to the warp

Based on the practical recommendations of operators and manufacturers, the following list of operating rules for plastering stations was compiled:

The processing of walls in the room begins from the corners, then the plaster mixture is applied to the joints of any structures, and only after that plastering the main area of the working surface;
The distance from the spray nozzle to the work surface must be strictly observed. As a rule, it is 20-30 cm, but it must be specified in the instructions for use issued by the manufacturer;
The outgoing jet of plaster should hit the work surface strictly perpendicularly;
The finishing mixture is applied in parallel stripes, each subsequent strip should overlap the previous one by 40-50%.

Remember! The higher the movement speed of the gun, the thinner the plaster layer.

Wall finishing process with a plaster station
PHOTO: petrovich.in.ua

Aligning the finish

The final stage of any plastering is the formation (leveling) of the treated surface. The easiest and fastest way to level the surface is by focusing on the beacons. The optimal processing time is not earlier than 20-30 minutes after application, but not later than 50-60 minutes. The exact time depends on the type of mortar, layer thickness and manufacturer's recommendations. Various tools can be used for alignment:

Rules;
Wide spatulas;
Plastering trowels;
Plastering machines.

The alignment process requires special attention in the corners and at the joints.

Leveling plaster in corners requires special attention
PHOTO: i.ytimg.com

Leading equipment manufacturers and their products

PFT. German manufacturer of plastering stations, whose products have proven themselves in the market.The most successful models are PFT G4 Smart and RITMO XL (new series of equipment). Despite the fact that the performance of comparable models of both series practically does not differ, the station of the PFT series is almost twice as large. The equipment operates from both single-phase and three-phase networks, there are also multi-voltage models (220V / 380V). Almost all reviews for the products of this manufacturer are positive, so if the high price does not scare you, then it is better to purchase them. Price range 250-300 thousand rubles.

PFT G4 Smart
PHOTO: c.allegroimg.com

Putzmeister. Another German manufacturer that has been producing construction equipment, including plastering stations, since 1958. In terms of functionality and cost, its models practically do not differ from the PFT series.

Putzmeister plastering station model MP 25
PHOTO: solatrade.ru

NOVO. Company headquarters registered in Germany, manufacturing facilities in China. Despite this, the products are distinguished by their reliability and high performance. Price range 200-250 thousand rubles. In addition, there are additional advantages in the design:

Possibility to connect an external compressor with a receiver;
Equipment water cooling.

NOVO Gen3 Complete Kit
PHOTO: novo.com.ru

Typhoon. Plastering station from a domestic manufacturer of the same name from Stavropol. The equipment is an extremely simplified and extremely unfortunate replica of the PFT Ritmo L-L4-2. Of the main disadvantages, users name:

Lack of electric motor power - costs 1.5 kW, you need at least 2.2 kW;
A compressor without a receiver - fails after a week of operation;
Leaking hopper welds - constantly leaking;
Low-performance screw pair - in fact, this unit is not produced independently, but is purchased from PFT from the Ritmo L-L4-2 model.

Plaster station Typhoon
PHOTO: i.ytimg.com

Other plastering stations of domestic production that can be found on the equipment market: Meteor, VEK, TSM 2, Hermes are even less successful copies of Typhoon.

Gallery: manual tools for small mechanization of applying plaster mixes:

: PHOTO: myshtukaturka.ru

: PHOTO: i.ytimg.com

: PHOTO: otdelka-expert.ru

: PHOTO: couo.ru

Summing up

Which is better hand or mechanized wall plastering? There is an unequivocal answer to this question - it is better to mechanize the process of plastering and grouting. At the same time, the choice of hand-held devices and plastering stations in the modern construction equipment market allows them to be purchased by both professionals and home craftsmen.

RATE THIS ARTICLE